User Manual of IRD811D Slide Switch Variant
Quick Start
- Insert battery: 2× 9V for kits supplied before May 2024, 1× 9V for kits supplied after May 2024.
- Connect the IRD521 sensor to the meter with the supplied cable (do not force connectors).
- Mount the sensor on the machine with the magnet.
- Slide the Power switch ON.
- Select unit with the Units slide: gSE / A / V / D.
- Select full-scale Range: 20 / 200 / 2000.
- Wait 2–3 s for the reading to settle, then note the value.
Introduction
IRD811D is a handheld Digital Vibration Meter cum Spike Energy / Bearing Health Checker. This article covers the older Slide Switch variant. It measures overall vibration (Acceleration, Velocity, Displacement) and Spike Energy (g SE) for early rolling-element bearing faults.
Key Specs
| Parameter | Value |
|---|
| Spike Energy | g SE |
| Acceleration | 0–20 g pk |
| Velocity | 0–200 mm/s RMS or mm/s pk (as ordered) |
| Displacement | 0–2000 µm pk-pk |
| Sensor | IRD521 accelerometer, 100 mV/g ±10% |
| Display | 3½-digit LCD, LOBAT at ≤ ~8.2 V DC |
| Power | 9V battery (1× or 2× by supply year), ~210 mAh+ |
Controls
- Power slide – switches the meter ON/OFF.
- Units slide – gSE (Spike Energy) / A (Acceleration) / V (Velocity) / D (Displacement).
- Range slide – full scale 20 / 200 / 2000. See full-scale range options. Use 20 for Acceleration, 200 for Velocity, 2000 for Displacement.
Battery
- Supplied before May 2024: 2× 9V.
- Supplied after May 2024: 1× 9V.
- Rechargeable or dry cell, ~210 mAh or higher. Recommended voltage 8.2–11.2 V DC (ideal ~9 V).
- Display shows LOBAT at about 8.2 V DC or below – replace/recharge.
Details: What batteries does IRD811D use?
Cable & Sensor
- Sensor: IRD521 accelerometer, 100 mV/g ±10%.
- Current standard cable: 2-pin MS (sensor end) ↔ 2-pin MRS (meter end), same family as IRD301/IRD306DP.
- Older kits may use a different connector – always use the cable supplied with your meter.
- Do not force connectors. Align and push gently.
How to Measure
- Mount the sensor firmly on a clean, flat spot close to the bearing.
- Power ON, select unit and the matching range.
- Wait 2–3 s for settle; record the reading.
- For bearing condition use gSE; for overall machine condition use Velocity.
- Take readings at the same points each time for trending.
Troubleshooting
| Symptom | Check |
|---|
| Blank display | Battery inserted? Correct count (1× or 2×) for your kit? Power slide ON? |
| LOBAT shown | Battery ≤ ~8.2 V – recharge or replace. |
| Reading stays 0 / unstable | Cable seated both ends, sensor firmly mounted, wait 2–3 s. |
| Over-range / 1 shown | Move Range slide to a higher full scale. |
| Connector will not fit | Do not force – use the cable supplied with this meter. |
Repair & Calibration
- National Traceable calibration at our Thane facility.
- Hand-carry in the morning → typically returned the same day; courier → about 1 week.
- Warranty: 1 year on portable instruments.
- Email service@irdmech.com · WhatsApp +91-9082527331
PDF Manual
The original PDF manual is still attached below as an optional download.
Related Articles
User Manual of IRD306DP Plus
Quick Start Install the correct number of 9V batteries for your meter’s manufacture date (see Battery). Connect the standard coiled cable between IRD306DP and IRD531. Use guide vanes — do not force connectors. Fit magnet or stinger firmly on IRD531 ...
User Manual of vbseries and SCOUT
User Manual of vbseries (vbBalancer, vbBalancer+, vb5, vb6, vb7 and vb8) SCOUT100 and SCOUT140 is attached.
User Manual of IRD811D Pro (V24 - Push Button Variant)
Quick Start Insert 1× 9V battery. Connect the IRD521 sensor to the meter with the coiled cable (MS end to sensor, MRS end to meter). Do not force. Fit the sensor on the magnet, slide off the safety plate, and mount on the machine. Press and release ...
IRD306 User Manual
Attached to this Article is the User Manual of IRD306 - Analog Vibration Meter manufactured by IRD Mechanalysis Limited.
User Manual of IRD449M
Attached to this article is the User Manual of IRD449M